Home > Industrial Products > Mezzanines >

[Discontinued] Southwest Solutions Mezzanine 16' x 17'
[Discontinued] Southwest Solutions Mezzanine 16' x 17'
 

(This product is no longer available)
Southwest Solutions Mezzanine 16' x 17'

16' x 17' Mezzanine structure with 125 PSF load rating.

[Discontinued]
Dimensions: 16' x 17' x 9' 10-1/4" (Height to Deck Surface)
Other: Clear Height 8' 2"


Availability: [Discontinued]
Product Code: SSG-101124
[Discontinued]

Description
 

Southwest Solutions Mezzanine 16' x 17'

Mezzanine Features

  • GENERAL: The mezzanine floor support and loading shall consist of 5" x 5” x 3/16” square columns with 5/8" thick X 12" square plates as bases. Column loading represents the maximum weight placed on the existing floor if the mezzanine is loaded to its maximum capacity on each square foot. The end-user should verify that their floor has adequate strength to support the column loading. The perimeter and intermediate support beams shall be structural beams. Joists shall consist of properly sized bar joists.
  • FLOOR DECKING (INCLUDED): 3/4" T & G Resindek LD with Gray Diamond Seal shall be used as an overlay attached by screws. Resindek LD supports live and dead pallet jack loads up to 2,000 lbs. Also available in Unfinished and Clear Diamond Seal®. This decking will include a 20 gauge galvanized b deck subsurface.
  • IBC STAIR SYSTEMS & HANDRAILS (INCLUDED): Application The stairs listed below meet the standards for FACTORY and STORAGE USE GROUPS with occupancies of 50 or less people. Treads shall be 42” wide with closed risers. Tread rise shall be a maximum of 7” and tread run shall be a minimum of 11”. Tread and closed riser material is to be steel diamond plate. Stair railing shall be constructed of 1 1/2” vertical posts and 1 1/2” horizontal tubes. Stair railings shall be 36” tall and shall be spaced so as to allow a sphere no larger than 21” diameter to pass through any opening. Landings shall be sized appropriately so as to meet code requirements. The landing floor is to be constructed of steel diamond plate. The landing railing shall be constructed of 1 1/2” vertical posts and 1 1/2” horizontal tubes. Landing railings shall be 42” tall and shall be spaced so as to allow a sphere no larger than 21” diameter to pass through any opening. All landing railing shall include a 4” tall toe plate.
  • OSHA 2 RAIL HANDRAIL (68 LINEAR FEET): The handrail shall consist of 42” tall 1 ½” tubular uprights with 1 ½” tubular cross members. 4” tall 14 gauge kick plate will also be supplied with the system. All handrails shall be powder coated safety yellow.
  • FASTENERS: All wedge anchors, bolts, nuts; washers, and screws shall be supplied with the system. No additional fasteners will be needed to complete the structure.
  • FINISH: All structural beams, columns, landings, handrails, and gates are powder coated in our standard colors. Bar joists are primed gray and are not powder coated. Special colors and powder coating of the bar joists can be quoted upon request. All handrails shall be painted safety yellow.
  • INCLUDED: Includes all design services, manufacturing, packaging, freight, inside delivery, installation by factory-certified (nonunion/non-prevailing wage) technicians during normal business hours, cleanup of the area, removal of all debris, and warranty. Assumes clear access to all loading docks, elevators, and installation sites.
  • NOTES & NOT INCLUDED: Because of market volatility impacting steel and aluminum, this price is valid until May 1, 2021.
    • Permitting (If Required) By Others
    • Foundations and/or Footers By Others
  • SSG